1V1T Prewired Harness, 2 Pickup 1Vol+1Tone, 2 500K Large Pots, 3Way Blade Switch

Description

1V1T Prewired Two Pickup Harness
HH or HS (SH) 2 Pot Standard Style
1 Volume Control Pot + 1 Tone Control Pot
2 Pickup Harness ~ 3 Way Blade Switch ~ Mono Jack
Brand New Dragonfire Pre-Wired Electric Guitar Wiring Harness
TNTCustomGuitars Item #: 1015
~~~~~~~~~~~~~~~~~~~~
ITEM DESCRIPTION~~~~~~~~~~~~~~~~~~~~
These hand-wired harnesses work well with most Two Pickup (i.e. Humbucker-Humbucker or Humbucker-Single) Systems. We offer many style and upgrade options along with typical replacements in standard and left-handed made-to-order wire harness versions. Each harness is unique and, based on order selections as well as current component stock on hand, may vary in appearance from the sample images. We wire to order and can accommodate many styles and preferences. Check our eBay Store Wiring Harness page for other variations and additional options. Message us; we’re happy to answer any questions.
This prewired harness features the following default options.
*1 Standard 3 Way Blade Switch
*1 Standard 500K Large/Long Volume Control Pot
*1 Standard 500K Large/Long Tone Control Pot
*1 Standard 0.047 Mylar Tone Cap
*1 Standard Mono Style Jack
Our 3-Way Blade Switch provides standard 3 Way pickup selections allowing for Bridge/Bridge-Neck/Neck options.
These harnesses use full-size large (quarter size), long-shaft, body mount control pots that work with most coarse knurled, 18-spline style knobs (sold separately). If you are going through a guard or have a non-standard set-up, you may need additional nuts/washers (sold separately) or other modification.
Our tone control capacitors help produce balanced bass, middle, and treble. This harness includes one Standard Mylar Chiclet Style tone cap.
Harness jacks work with standard cables only and jack sockets accept standard ¼” plugs.
A Mono Jack open-frame jack is included; this jack requires a 9mm mounting hole and tightens to your jack plate (sold separately).
Soldering is required for installation.
We provide basic instructions posted in the item images to show the connections you’ll need to solder. Please know your abilities, requirements, measurements and needs to make sure this item will work for you. We are available to answer any questions before you buy.
~~~~~~~~~~~~~~~~~~~~
APPROXIMATE MEASUREMENTS
~~~~~~~~~~~~~~~~~~~~
*Overall Switch Height: 48mm
*Switch Insertion Depth: 28mm
*Switch Dimensions: 38mm (length) x 27mm (width)
*Switch Screw Spacing (center:center): 41mm
*Pot Shaft Length: 18mm
*Pot Dimensions: 24mm (diameter) & 30mm (height)
*Pot Requirements: 10mm (hole diameter) & 12mm (depth)
*Mono Jack Length: 15mm (without pins)
*Mono Jack Diameter (Mounting Hole Required): 9mm
*8” Insulated Wire Length
Variability is to be expected as measurements provided are approximations.
Ask any questions regarding options, measurements, installation, special requests, etc. prior to purchase.
~~~~~~~~~~~~~~~~~~~~
WHAT’S INCLUDED (What You Get)
~~~~~~~~~~~~~~~~~~~~
*1 Prewired Guitar Wiring Harness Kit
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.
~~~~~~~~~~~~~~~~~~~~PURCHASE NOTES~~~~~~~~~~~~~~~~~~~~
Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items. ASK ANY QUESTIONS PRIOR TO PURCHASE! We accept returns (see policy link for details); BUYERS ARE RESPONSIBLE FOR RETURN SHIPPING. We are here to help with any questions prior to purchase to avoid the need for a return. Use, installation, modification or any other alteration to the product voids the possibility of a return.
This harness will not work with non-standard set-ups. Due to the vast and varied nature of possible set-ups and user expertise, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Soldering is required. Depending on your set-up, you may require adjustment – DO NOT PURCHASE if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications (if needed).
Depending on your current or desired set-up, installation may require extra care, accuracy, or advanced skill. You should be able to use knowledge of wiring and your own diagram or instructions and experience to install. Note that we do not recommend installation using power tools as these can put too much force on the product and cause damage. Installation is best with moderate heat only (don’t have your iron too hot). This item is prewired. If your set-up requires you to disconnect the wires, be sure to take a picture or make note of the connections so you can reattach (solder!) properly. We do not recommend a clip/tie method for installation. Pay attention during install to avoid damage; components are sensitive. Excessive or prolonged heat can cause irreparable damage. We do not provide technical or any other type of support for installation, configuration, modification, or use of this item. Do not purchase if you are unsure of your ability to successfully complete installation.
ALLOW AND EXPECT variation in color due to photo and monitor settings as well as natural product variance. Color, sound, performance, or other descriptions are subjective as well as generic in nature. YOUR OUTCOME WILL VARY based on many factors, most importantly your equipment, environment, perception, skill, style, and experience. Color descriptions indicate color only, not material. Due to the production/machining process, some natural variation and imperfection may be expected in the finish of items. Mirror or reflective style finishes may reflect your individual environment and impact overall appearance.
We reserve the right to wire in any style or method we choose. As unique creations, not mass produced, sample images may not exactly reflect what you will receive. Additionally, your option/product selections will be wired to order and your final product will be unique to your order request as well as our current component stock on hand. We reserve the right to make substitutions of equal or better value/performance at our discretion. Though performance outcome is constant and all items are tested prior to shipping, each of our techs has their own personal style for wiring and images are provided only as examples.
TNTGuitars and Dragonfire Guitars are neither associated nor affiliated with any other brands. All registered trademarks belong to their respective owners.
CONTACT US PRIOR TO PURCHASE if you have any questions or concerns regarding color, pattern, fit, materials, installation requirements, compatibility with your instrument, measurements provided, or anything else.
INSPECT YOUR ORDER CAREFULLY UPON RECEIPT for any shipping damage and general appearance. DO NOT use, modify or install the product if anything does not meet with your approval for any reason. Message us right away; we pledge to address any problems or concerns you have PRIOR to installation. If everything is in order upon receipt, simply install carefully to enjoy.
Read the information provided for shipping and returns before you buy. Reference our Store Pages Links carefully for store policies and additional product details. ASK ANY QUESTIONS PRIOR TO PURCHASE!